Leopard II Home Automation Touchscreen Controller - X10 - Applied Digital

The intelligent control system with touchscreen for your home automation: Up to 1.024 different infrared commands - send and receive - and programme code produced automatically up to 4.096 lines. Central processing unit for all ADI products and real bidirectional X10 communication.

Features:

• Fully programmable, if-then-else control.
• Touchscreen with 320 x 240 pixels resolution and 25 freely configurable display pages.
• Over 4,000 lines of programmable code.
• Infrared send and receive.
• 2 way X10.
• RS-485 expansion to a variety of low cost I/O modules.
• Comes with easy-to-use CMax Control Wizard Software.
• The perfect controller for use with HomeSeer!

Operation:
Connect the Leopard with the enclosed cables with a free serial port of your PC as well as with the Powerline Interface XM10 (not included). Now connect the power supply (9 - 12V DC or AC, at least 1,500mA recommended, dependent on the number of connected ADI products, not included) and install the enclosed CMax software. You can now programme your Leopard according to your wishes and needs and teach it the desired infrared commands with CMax. The CMax software is very easy to use so you will get satisfying results very fast even without English knowledge. After you have finished transmit your program into the internal memory of the Leopard. You can now disconnect it of your PC.

Application:
The Leopard has practically unlimited programming possibilities. For every X10 module time settings are programmable on day, weeks, periods or annual basis. Automatic setting to summer and wintertime. It calculates sunrise and sunset times by using your geographical position. Of course several settings per module are also possible. For lamp modules the light level can be preprogrammed in %. The CMax software uses logical "if-then" combinations, so that it executes further actions like a X10 command, an infrared command or a command for another ADI product when the desired condition applies. The conditions can be based also on infrared signals or data received by other ADI products besides the conditions mentioned before.
All settings are programmed in the non volatile memory (EEPROM) of the interface so that they are not lost at power failure either.

Technical information:

• Case: Provided for cavity mount
• Mounting cut-out: L188 x W143mm, mounting template included
• Power supply: 9 - 12V AC oder DC, 1,000mA
• Firmware: 4,096 lines program code, 64 timers, 128 variables, 1,024 IR commands, real time clock
• Piezo buzzer: integrated, adjustable
• Infrared receiver: integrated

Touchscreen:

• Display: 320 x 240 pixel, QVGA-LCD, monochrom, CCFL background lighting
• Touch points: 60, 10 x 6 grid
• Display pages: 25
• Objects: 256 total, every combination of text, graphics and buttons
• Buttons: 6 different sizes
• Live-Text: Text can be updated by programme variables like time, temperature etc.

Connections:

• I/O: RS232 - DBSF with 1.8m cable
• X10 (to XM10): RJ11 with 1.8m cable
• ADNET: 2 screw terminals
• Power supply: 2 screw terminals
• Infrared input: 2 screw terminals
• Infrared output: 3.5mm stereo jack
• All above-mentioned connections and an additional infrared input are also available in a composite connection bar.

System requirements:

• Powerline Interface XM10 (not included)
• Power supply 12V DC or AC min. 1,000mA, dependent on the number of connected ADNET modules (not included)

Set contains:

• CMax software, CD-ROM
• RJ11 cable 1.8m
• RS232 cable 1.8m
• Mounting template
• Manual

Note: This product is also available as set with "XM10 Powerline Interface" or as SmartHomeSeer Leopard Kit!